Tire size difference in inches · Same wheel diameter
245/75R17 vs 265/70R17
265/70R17 is 0.14 in (3.5 mm, 0.44%) taller than 245/75R17. Section width 0.79 in wider. Sidewall 0.07 in taller. At an indicated 60 mph you'd be doing about 60.26 mph.
When replacing 245/75R17 with 265/70R17
- Overall diameter
- 31.47 → 31.61 in
- +0.14 in (+3.5 mm), +0.44%
- Section width
- 9.65 → 10.43 in
- +0.79 in (+20.0 mm)
- Sidewall height
- 7.23 → 7.30 in
- +0.07 in (+1.8 mm), +0.95%
- Ride height
- +0.07 in
- +1.8 mm, half the diameter change
- Dash reads 60 mph
- 60.26 mph
- +0.26 mph actual vs indicated
- Revolutions per mile
- 641 → 638
- -0.44%, nominal
Each value is rounded on its own, so a change can differ by 0.01 in from the difference between the rounded sizes.
Open this comparison in the interactive calculatorVehicle compatibility not checked. Diameter difference within 3%. These results compare nominal dimensions. They do not confirm vehicle fitment. Actual clearance varies by tire model, approved rim width, wheel construction, suspension, alignment, body tolerances, steering angle, load, and brake geometry. Verify load and speed ratings and physically test-fit the complete setup before driving.
Tire dimensions only. Wheel width and offset are not assumed on this page, so fender-side and suspension-side position changes are not calculated. Enter your wheel specifications in the calculator for those estimates. How we calculate
What changes from 245/75R17 to 265/70R17
- Speedometer: at an indicated 60 mph you're actually doing about 60.26 mph, and about 70.31 mph at an indicated 70 mph.
- Odometer: for every 10,000 miles it shows, you'll have driven about 10,044 miles, 44 more than shown.
- Engine speed: wheel revolutions per mile go from 641 to 638, so at the same road speed the engine turns about 0.44% slower in any given gear.
- Width: 265/70R17 is 0.79 in (20.0 mm) wider. Centered in the same place, each sidewall moves about 0.39 in (10.0 mm) outward; wheel width and offset decide the real position.
- Both sizes mount on 17 in wheels. Check that your wheel width is inside the approved rim-width range for 265/70R17.
- The profile moves from very tall (75 series) to tall (70 series).
- A 20 mm width change can move the approved rim-width range far enough that your current wheel falls outside it. Confirm the range for the exact tire model before buying wheels or tires.
- For scale, the 0.14 in diameter change is less than the roughly 0.5 in a tire loses as its tread wears from a typical new 10/32 in to the 2/32 in wear bars. Over a tire's life, wear alone changes the speedometer reading more than this swap does.
- Some sizes in this range also come as LT (light truck) tires. A P-metric and an LT tire of the same size carry different loads at the same pressure, so match the load index or load range the vehicle requires, not just the size.
Going from 265/70R17 to 245/75R17 instead: 0.44% shorter; an indicated 60 mph is about 59.74 mph. Open 265/70R17 to 245/75R17 in the calculator
How the setup changes
Proposed 265/70R17 is 0.14 in taller overall.
Shared center and scale. Circles compare diameter and rim size, not loaded ride height.
Speedometer
Indicated vs actual
| Dash reads | Estimated speed |
|---|---|
| 30.00 mph | 30.13 mph |
| 60.00 mph | 60.26 mph |
| 70.00 mph | 70.31 mph |
Assumes the speedometer was accurate with the current tires. Uses diameter ratio.
Detailed comparison
Changes are proposed minus current. Nominal rev/mile uses geometric circumference, not measured rolling circumference. Values round independently; rounded columns may not subtract exactly. Wheel specifications retain industry notation.
| Measurement | 245/75R17 | 265/70R17 | Change |
|---|---|---|---|
| Tire size | 245/75R17 | 265/70R17 | — |
| Nominal section width | 9.65 in (245.0 mm) | 10.43 in (265.0 mm) | +0.79 in (+20.0 mm) |
| Rim diameter | 17 in | 17 in | ±0.00 in (±0.0 mm) |
| Overall diameter | 31.47 in (799.3 mm) | 31.61 in (802.8 mm) | +0.14 in (+3.5 mm) |
| Radial sidewall estimate | 7.23 in (183.8 mm) | 7.30 in (185.5 mm) | +0.07 in (+1.8 mm) |
| Geometric circumference | 98.86 in (2,511.1 mm) | 99.29 in (2,522.1 mm) | +0.43 in (+11.0 mm) |
| Revolutions per mile | 641 (nominal) | 638 (nominal) | -3 |
| Diameter change | — | — | +0.44% |
| Ride-height estimate | — | — | +0.07 in (+1.8 mm) |
Physical checks
- Approved rim-width range for the exact tire model.
- Load index and speed rating equal to or greater than vehicle requirements.
- Brake-caliper, hub, and wheel-fastener compatibility.
- Fender, liner, suspension, and full-lock steering clearance.
- Clearance at full compression and under expected load.
- Alignment, tire pressure, and manufacturer guidance.
- Professional inspection when variance or clearance is uncertain.
Related single-size calculators
Related comparisons
Review record
Automated dimensional check against the FitMyTires publication policy (v1) on August 19, 2026. The check covers size data and calculations, not vehicle fitment. Read the editorial and corrections policy.